outside calipers External card gauge NA.NA.650102

 OUTSIDE CALIPERS NA.NA.650104

 CALIPER OUTSIDE 400MM， NA.NA.650108

 SPRING OUTSIDE CALIPERS, SIZE = 100MM NA.NA.650121

 SPRING OUTSIDE CALIPERS NA.NA.650123

 SPRING OUTSIDE CALIPERS- 250mm NA.NA.650125

 "CALIPER INSIDE 100MM, FOR MEASURING THE INSIDE

DIAMETER OF PIPES, FITTINGS, ETC. MADE OF

HARDENED STEEL WITH POINTS OF TEMPERED STEEL TO

PREVENT WEAR." NA.NA.650151

 inside calipers Inner card gauge NA.NA.650155

 SPRING INSIDE CALIPERS, SIZE = 100MM NA.NA.650171

 650173 CALIPER INSIDE WITH SPRING 150MM NA.NA.650173

 CALIPER INSIDE WITH SPRING    250MM NA.NA.650175

 650215 COMPASS STEEL 200MM NA.NA.650215

 SPRING DIVIDERS NA.NA.650234

 MICROMETER,OUTSIDE 0-25mm,IN 0.01mm GRADUATION NA.NA.650301

 OUTSIDE MICRO METER, RANGE 25-50mm,650302 NA.NA.650302

 OUT SIDE MICROMETER (50-75) NA.NA.650303

 OUT SIDE MICROMETER (75-100) NA.NA.650304

 OUTSIDE MICROMETER 100 - 200 NA.NA.650305

 OUTSIDE MICROMETER 100 - 200 NA.NA.650306

 OUTSIDE MICRO METER, 650383, RANGE 150-300mm NA.NA.650383

 "MICROMETER INSIDE TUBULAR, 50-63MM IN 0.01MM

GRADUATION, A SINGLE ROD TYPE MICROMETER MADE

FROM STRONG BUT LIGHT TUBING. THE MEASURING

ANVILS ARE GROUND TO A RADIUS TO BE USED ON

EITHER FLAT OR CURVED SURFACES. GRADUATED IN

0.01 MM INCREMENTS. MICROMETERS WITH COUNTER

DISPLAYS ARE ALSO AVAILABLE UPON REQUEST." NA.NA.650401

 "MICROMETER INSIDE JOINTED ROD, 50-150MM 0.01MM

STEP, EACH SET OF THE ANVILS FOR THE JOINTED

INSIDE MICROMETERS IS ADJUSTED TO SUIT THE

PARTICULAR MICROMETER. EACH IS GIVEN A MARK AND

MUST NOT BE USED ON ANY OTHER MICROMETER.

WHEN ASSEMBLING, CLEAN THE JOINING FACES

PERFECTLY. GRADUATED IN 0.01 MM INCREMENTS." NA.NA.650441

 INSIDE MICROMETER (50-300)MM  for A/E NA.NA.650442

 "MICROMETER INSIDE CALIPER, 5-30MM 0.01MM STEP,

THIS CALIPER TYPE JAW FACILITATES QUICK READING

FOR INTERNAL GROOVES OF ALL TYPES INCLUDING “O”

RINGS, SEALS, OIL GROOVES, WASHER GROOVES AS

WELL AS BORES AND RECESSES. GRADUATED IN 0.01

MM INCREMENTS IN SIZES FROM 25 MM TO 150 MM.

MICROMETERS UP TO 50 MM IN SIZE WITH COUNTERS

ARE ALSO AVAILABLE." NA.NA.650451

 "MICROMETER DEPTH 0-25MM, IN 0.01MM BASE WIDTH

63.5MM, MEASURES THE DEPTH OF HOLES,

PROJECTIONS, ETC. PROVIDED WITH A HARDENED TIP

AND THREADED GROUND SCREW, ADJUSTABLE FOR

WEAR. THE FACE OF THE BASE IS HARDENED AND

PLANED TO MAINTAIN A LEVEL SURFACE. GRADUATED IN

INCREMENTS OF 0.01 MM." NA.NA.650471

 "MICROMETER DEPTH 0-200MM, IN 0.01MM WITH SLIDABLE

ROD, BASICALLY THE SAME INSTRUMENT AS THE DEPTH

MICROMETER BUT WITH A GRADUATED SLIDING ROD.

THE BASE LENGTH FOR ALL MICROMETERS IS 120 MM.

GRADUATED IN INCREMENTS OF 0.01 MM. THE DIAMETER

OF THE ROD IS 6 MM." NA.NA.650476

 CAL IPER VERNIER STAINL ESS, STEEL METRIC 1 50MM NA.NA.650502

 VERNIER CALIPERS NA.NA.650504

 VERNIER CALIPERS NA.NA.650506

 STEEL COMPASS NA.NA.650221

 VERNIER DEPTH GAUGES, LENGTH = 150MM NA.NA.650536

 VERNIER DEPTH GAUGES, LENGTH = 250MM NA.NA.650538

 塞尺0.05-1.00mm,品牌上工 NA.NA.650551

 THICKNESS GAUGE #100A10， 0.03-0.30MM 100MM LENGTH， NA.NA.650552

 "THICKNESS GAUGE #75A13, 0.03-3.0MM 75MM LENGTH,

PARTICULARLY POPULAR WITH MACHINISTS AND TOOL

MAKERS FOR GAUGING NARROW SLOTS AS WELL AS FOR

ADJUSTING THE AIR GAPS OF VALVES ON MOTORS. THE

LEAVES ARE MADE OF TEMPERED STEEL AND HAVE THE

THICKNESS MARKED ON THEM. THE GAUGES LISTED

BELOW ARE CLASSIFIED AS A TYPE BECAUSE THEY HAVE

STRAIGHT LEAVES. TYPE B GAUGES WITH TAPERED

LEAVES ARE ALSO AVAILABLE UPON REQUEST. IN

METRIC" NA.NA.650556

 OIL GAUGING TAPES, 30M/100", WHITE TAPE NA.NA.650558

 FEELER GAUGE FOR CLEARANCE MEASUREMENTS NA.NA.650560

 Thickness gauges, (Feeler gauge), 150A25 NA.NA.650564

 Screw pitch gauges (threaded gauges) 55 degree no. 137 Whitworth NA.NA.650601

 Screw pitch gauges (threaded gauges) 60 degree no.156  metric NA.NA.650602

 SCREW PITCH GAUGE #ISO METRIC 60DEG 0.2-6.0 PITCH NA.NA.650605

 SCREW PITCH GAUGE NA.NA.650603

 SCREW PITCH GAUGE NA.NA.650604

 CENTRE GAUGE, WHITWORTH NA.NA.650631

 CENTER GAUGE 60DEG, METRIC STANDARD NA.NA.650633

 "MEASURING CUP STAINLESS STEEL, 0.5LTR, STAINLESS

STEEL OR PLASTIC MADE CUP FOR MEASURING LIQUID

VOLUME. GRADUATED IN LITERS ONLY. STAINLESS

STEEL" NA.NA.174032

 MEASURING CUP PLASTIC 1.0LTR NA.NA.174028

 Scales ， adult ， weighing ， clinical ， capacity 150 kg NA.NA.650768

 "SPRING BALANCE DIAL HOOK TYPE, CAPACITY 30KGS,

PAINTED METAL CASE WITH BRASS DIAL AND WHITE

MARKINGS, SHOCK ABSORBING MECHANISM AND ZINC

PLATED HOOK. MULTIPURPOSE USE (WEIGHING COLD

STORES, BULK FOODS, ETC)." NA.NA.650753

 "SCALE SPRING BALANCE, CAPACITY 8KGS, FOR

WEIGHING ITEMS IN BULK. CAPACITY RANGE FROM 200

GRAMS TO 50 KILOGRAMS. AVAILABLE IN METRIC

GRADUATION ONLY. PLASTIC OR STEEL PLATFORM

TRAYS." NA.NA.174007

 STAINLESS STEEL STRAIGHT RULERS, 300MM NA.NA.650802

 STAINLESS STEEL STRAIGHT RULER NA.NA.650803

 Stainless steel straight rules  length 1000mm NA.NA.650804

 RULE CONVEX STEEL METRIC 2MTRS NA.NA.650821

 RULE CONVEX STEEL METRIC 5MTRS NA.NA.650823

 OIL GAUGING TAPE, STEEL, S. STEEL, METRIC, 20MTRS NA.NA.650872

 TAPE , OIL GAUGE , STEEL AND BLACK TAPE , METRIC , 20 METERS. NA.NA.650862

 WATER FINDING PASTE 75GRM YELLOW TO RED NA.NA.650890

 GASOLINE AND OIL FINDING PASTE 75GRM BLUE TO RED NA.NA.650891

 STEEL STRAIGHT EDGES NA.NA.650901

 STEEL STRIGHT EDGES NA.NA.650904

 precision flat try squares 150X100 NA.NA.650940

 TRY SQUARE PRECISION FLAT, 1ST-GRADE(+_0.02) 200X130MM NA.NA.650941

 PRECISION TRY SQUARES WITH BASE, 300 X 200 NA.NA.650973

 "VEE BLOCK A-TYPE 150MM, MACHINE FINISHED AND

MADE OF CAST IRON. TWO TYPES AVAILABLE, THE A

TYPE WHICH IS COMPOSED OF THREE 90O V-SHAPED

INDENTATIONS OF VARIOUS DEPTHS AND THE B TYPE

WHICH HAS ONE 90O V-SHAPED INDENTATION. A SET OF

TWO PIECES CAN BE USED IN MECHANICAL PROCESSING

AND INSPECTION AS A HOLDING TABLE FOR MARKING

OFF ROUND RODS AND RIGHT ANGLE BODIES, OR TO

HOLD ROUND MARKS. AN A TYPE BLOCK EQUIPPED WITH

A CLIP IS ALSO AVAILABLE UPON REQUEST." NA.NA.651055

 "LEVEL BENCH CAST-IRON 450MM, A POPULAR LEVEL

MADE OF CAST IRON. PROVIDED WITH A LEVEL VIAL AND

A PLUMB VIAL." NA.NA.651080

 "TACHOMETER HAND HORN TYPE, 400-5000RPM, THIS

TACHOMETER INDICATES SPEED INSTANTANEOUSLY AND

THEREFORE ENABLES SPEED FLUCTUATIONS TO BE

READ OFF THE DIAL. A CIRCUMFERENCE DISC IS

PROVIDED TO MEASURE THE CIRCUMFERENCE SPEED.

10 REVOLUTIONS OF THIS DISC IS EQUAL TO 1 MTR. SO

BY DIVIDING THE NUMBER INDICATED ON THE GAUGE BY

10, YOU CAN DETERMINE THE NUMBER OF REVOLUTIONS

PER MINUTE. WHEN ORDERING, INDICATE THE RPM

CAPACITY FROM THE LIST BELOW." NA.NA.651301

 DIAL GAUGE STANDS, MAGNETIC BASE NA.NA.651427

 DIAL GAUGE FOR MAGNETIC BASE STANDS, STANDARD, RANGE-5 mm,    GRADUATION-0.01mm, BOLTED WITH STAND NA.NA.651402

 "PRESSURE CALIBRATOR 0 TO, 700BAR SCANSENSE

PM310H, PM310H – FOR HIGH PRESSURE CALIBRATION:

USING PM305 TOGETHER WITH A HYDRAULIC PUMP A

UNIQUE HANDHELD HIGH PRESSURE CALIBRATOR

NAMED PM310H. ORIGINALLY DESIGNED FOR USE ON

NORTH SEA PLATFORMS, THE PM310H IS EXTREMELY

RUGGED AND IS MADE FOR FIELD USE. USING OIL OR

WATER AS A PRESSURE MEDIUM, THE PM310H GENERATES PRESSURE UP TO 700 BAR (G) WITH

ACCURACY OF 0.03% FS. PM310H IS SUPPLIED READY

TO USE IN CARRYING CASE COMPLETE WITH TEST HOSE

AND FITTINGS." NA.NA.651579

 CABIN THERMOMETERS NA.NA.651701

 "THERMOMETER FOR REFRIGERATOR, STAINLESS W/MAGNET -30TO50DEG

A wide variety of types are available. The most common types are listed below.

Part Name:  THERMOMETER FOR REFRIGERATOR, STAINLESS W/MAGNET - 30TO50DEG

Part Desc:  A wide variety of types are available. The most common types are listed below.

Equipment Name:  Thermometer for Refrigerator

Mfg PartNo.:    651716

Manufacturer Name:  IMPA CATALOG(VER.6)" NA.NA.651716

 "SURFACE THERMOSENSOR STANDARD, 900DEG.C FOR

TMDT2, A HANDY, ECONOMICAL, COMPACT

THERMOMETER WHICH CONSISTENTLY PROVIDES HIGH

PRECISION AND ACCURACY REGARDLESS OF

ENVIRONMENTAL CONDITIONS. DESIGNED TO WORK

EFFECTIVELY WITHOUT MUCH POWER AND WILL WORK

CONTINUOUSLY. AN ASSORTMENT OF TEMPERATURE

PROBES ARE AVAILABLE TO ACCOMMODATE DIFFERENT

APPLICATIONS. MOST COMMONLY USED TO MONITOR

BEARINGS, PUMPS, ELECTRICAL MOTORS AND OTHER

HEAT GENERATING MACHINERY.

THERMOSENSORS FOR DIGITAL THERMOMETER:

VARIOUS TYPES OF THERMOSENSORS DESIGNED FOR

USE WITH THE ABOVE MENTIONED THERMOMETERS ARE

LISTED BELOW WITH THEIR RESPECTIVE

SPECIFICATIONS." NA.NA.651771

 EMP MEASURE DEVICE INFRARED, TEMP MEASURE DEVICE INFRARED NA.NA.651804

 Calibrator Temp Sika Tp17 650m, Range Upto 650deg.c 230vac NA.NA.652509

 INSPECTION MIRROR (EXTENSION SHAFT) NA.NA.652703

 UNILEVER PURE IT CLASSIC 23 LITRES GERM KILL KIT NA.NA.652704

 INSPECTION FLASLIGHT WITH MIRROR NA.NA.652708

 Tester NA.NA.795722

 CLAMP METER CM5, TRUE RMS, 0.1 A TO 60A/400A/600A NA.NA.795735

 "AVO METER AX-313TR, UNIVERSAL POLARITY, THESE ARE

MATCHED, PORTABLE INSTRUMENTS; HIGHLY ACCURATE

FOR INDUSTRIAL ELECTRICITY TESTING. THEY ARE

DESIGNED TO MEET THE REQUIREMENTS OF MOST

INDUSTRIAL TEST SITUATIONS. CARRYING CASES ARE

AVAILABLE FOR ALL MODELS. THE SPECIFICATIONS

LISTED BELOW ARE FOR YOUR REFERENCE." NA.NA.795744

 DIGITAL MULTI TESTER COMPACT SYSTEM F NA.NA.795767

 MULTI TESTER DIGITAL COMPACT MODEL CD-800a NA.NA.795756

 "INSULATION TESTER 0-300V, 500V/1000MOHM, AN ALL-

TRANSISTOR INSULATION RESISTANCE TESTER FEATURING SIMPLE PUSH-BUTTON, OPERATION. IT HAS A

VOLTMETER SCALE FOR MEASURING AC VOLTAGE IN

ADDITION TO INSULATION RESISTANCE. THIS PORTABLE

INSTRUMENT IS USED FOR INSULATION RESISTANCE

MEASUREMENT OF ELECTRICAL MACHINES AND

DEVICES, CONTROL AND SWITCHING EQUIPMENT,

POWER LINE AND CABLE WIRING, AS WELL AS OTHER

APPLICATIONS." NA.NA.795777

 HEAT DETECTOR TESTERS NA.NA.331071

 SMOKE DETECTOR TESTER NA.NA.331073

 SPARE TEST GAS 35OGM NA.NA.331074

 SMOKE DETECTOR TEST  SPRAY NA.NA.331077